When and why should I use Category 6 over 5E cable?
If you plan to remain in your current location long term, category 6 can be a better investment. Category 6 cable offers improved transmission performance, has greater bandwidth, and is backward compatible to cat 5e. If you have a short term lease and you don’t have or anticipate a requirement for large bandwidth, then category 5e is the more cost effective solution. MORE…
Can you move my phone system?
Yes. IBC has successfully moved NEC, Nortel and many other phone systems during company relocations. As your telecommunications solutions provider we always strive to find the most efficient and cost effective options for each situation, whether moving or installing new systems equipment.
Can you assist with my phone/data services relocation? Can you recommend a new service provider?
Yes. IBC has extensive experience and knowledge working with service providers and we know how to relocate service to minimize downtime. IBC will coordinate and follow through on all aspects or phone relocation. We can contact or recommend several service providers for you. Recommended providers may be able to offer you a better, more cost effective solution to your voice and data needs.
Why do I need all the bandwidth of category 6? As far as I know, there is no application today that requires 200 MHz of bandwidth.
Bandwidth precedes data rates just as highways come before traffic. Doubling the bandwidth is like adding twice the number of lanes on a highway. The trends of the past and the predictions for the future indicate that data rates have been doubling every 18 months. Current applications running at 1 Gb/s are really pushing the limits of category 5e cabling. As streaming media applications such as video and multi-media become commonplace, the demands for faster data rates will increase and spawn new applications that will benefit from the higher bandwidth offered by category 6. This is exactly what happened in the early 90’s when the higher bandwidth of category 5 cabling compared to category 3 caused most LAN applications to choose the better media to allow simpler, cost effective, higher speed LAN applications, such as 100BASE-TX. Note: Bandwidth is defined as the highest frequency up to which positive power sum ACR (Attenuation to Crosstalk Ratio) is greater than zero.
What is the general difference between category 5e and category 6?
The general difference between category 5e and category 6 is in the transmission performance, and extension of the available bandwidth from 100 MHz for category 5e to 200 MHz for category 6. This includes better insertion loss, near end crosstalk (NEXT), return loss, and equal level far end crosstalk (ELFEXT). These improvements provide a higher signal-to-noise ratio, allowing higher reliability for current applications and higher data rates for future applications.
Will category 6 supersede category 5e?
Yes, analyst predictions and independent polls indicate that 80 to 90 percent of all new installations will be cabled with category 6. The fact that category 6 link and channel requirements are backward compatible to category 5e makes it very easy for customers to choose category 6 and supersede category 5e in their networks. Applications that worked over category 5e will work over category 6.
What does category 6 do for my current network vs. category 5e?
Because of its improved transmission performance and superior immunity from external noise, systems operating over category 6 cabling will have fewer errors vs. category 5e for current applications. This means fewer re-transmissions of lost or corrupted data packets under certain conditions, which translates into higher reliability for category 6 networks compared to category 5e networks.
When should I recommend or install category 6 vs. category 5e?
From a future proofing perspective, it is always better to install the best cabling available. This is because it is so difficult to replace cabling inside walls, in ducts under floors and other difficult places to access. The rationale is that cabling will last at least 10 years and will support at least four to five generations of equipment during that time. If future equipment running at much higher data rates requires better cabling, it will be very expensive to pull out category 5e cabling at a later time to install category 6 cabling. So why not do it for a premium of about 20 percent over category 5e on an installed basis?
What is the shortest link that the standard will allow?
There is no short length limit. The standard is intended to work for all lengths up to 100 meters. There is a guideline in ANSI/TIA/EIA-568-B.1 that says the consolidation point should be located at least 15 meters away from the telecommunications room to reduce the effect of connectors in close proximity. This recommendation is based upon worst-case performance calculations for short links with four mated connections in the channel.
Why wouldn’t I skip category 6 and go straight to optical fiber?
You can certainly do that but will find that a fiber system is still very expensive. Ultimately, economics drive customer decisions, and today optical fiber together with optical transceivers is about twice as expensive as an equivalent system built using category 6 and associated copper electronics. Installation of copper cabling is more craft-friendly and can be accomplished with simple tools and techniques. Additionally, copper cabling supports the emerging Data Terminal Equipment (DTE) power standard under development by IEEE (802.3af).
What is meant by the term "Electrically Balanced"?
A simple open wire circuit consisting of two wires is considered to be a uniform, balanced transmission line. A uniform transmission line is one which has substantially identical electrical properties throughout its length, while a balanced transmission line is one whose two conductors are electrically alike and symmetrical with respect to ground and other nearby conductors.* "Electrically balanced" relates to the physical geometry and the dielectric properties of a twisted pair of conductors. If two insulated conductors are physically identical to one another in diameter, concentricity, dielectric material and are uniformly twisted with equal length of conductor, then the pair is electrically balanced with respect to its surroundings. The degree of electrical balance depends on the design and manufacturing process. Category 6 cable requires a greater degree of precision in the manufacturing process. Likewise, a category 6 connector requires a more balanced circuit design. For balanced transmission, an equal voltage of opposite polarity is applied on each conductor of a pair. The electromagnetic fields created by one conductor cancel out the electromagnetic fields created by its "balanced" companion conductor, leading to very little radiation from the balanced twisted pair transmission line. The same concept applies to external noise that is induced on each conductor of a twisted pair. A noise signal from an external source, such as radiation from a radio transmitter antenna generates an equal voltage of the same polarity, or "common mode voltage," on each conductor of a pair. The difference in voltage between conductors of a pair from this radiated signal, the "differential voltage," is effectively zero. Since the desired signal on the pair is the differential signal, the interference does not affect balanced transmission. The degree of electrical balance is determined by measuring the "differential voltage" and comparing it to the "common mode voltage" expressed in decibels (dB). This measurement is called Longitudinal Conversion Loss "LCL" in the Category 6 standard. * The ABC’s of the telephone Vol. 7
See the full article
For additional information and definition of terms, please see our glossary.